Technical Parameters
|
Technical parameter |
Parameter value |
|
Brand |
XUNCHIP |
|
Radioactivity measuring range |
0~2000W/M2 |
|
Radioactivity allow deviation |
±7% |
|
Repeatability test |
±5% |
|
Radioactivity detection chip |
Import digital |
|
Wavelength range |
380nm~730nm |
|
Interface |
RS485/4-20mA/DC0-10V |
|
Power |
DC6~24V 1A |
|
Running temperature |
-30~85℃ |
|
Working humidity |
5%RH~90%RH |
Product Selection
Product DesignRS485,4-20mA,DC0-10VMultiple output methods, the products are divided into the following models depending on the output method.
|
Product model |
output method |
|
XM8580B |
RS485总线 |
|
XM8580M |
4-20mA |
|
XM8580V10 |
DC0-10V |
Product Size
Why choose this product?
How to use?
Application solution
Product List
Pictures
Communication Protocol
The product uses RS485 MODBUS-RTU standard protocol format, all operation or reply commands are hexadecimal data. The default device address is 1 when the device leaves the factory, and the module or NON-Recorder default baud rate is 9600,8,n,1 ,but data recorder default baud rate is 115200 .
1. Read data (function code 0x03)
Inquiry frame (hexadecimal), sending example: query 1 data of 1# device, the upper computer sends the command: 01 03 00 00 00 01 84 0A .
|
Address |
Function Code |
Start Address |
Data Length |
Check Code |
|
01 |
03 |
00 00 |
00 01 |
84 0A |
For the correct query frame, the device will respond with data: 01 03 02 00 79 79 A6 , response format:
|
Address |
Function Code |
Length |
Data 1 |
Check Code |
|
01 |
03 |
02 |
00 79 |
79 A6 |
Data description: The data in the command is hexadecimal, take data 1 as an example, 00 79 is converted to decimal value as 121, assuming the data magnification is 100, then the real value is 121/100=1.21, Others and so on.
2. Common data address table
|
Configuration Address |
Register Address |
Register Description |
Data Type |
Value Range |
|
40001 |
00 00 |
Radioactivity |
Read Only |
0~65535 |
|
40101 |
00 64 |
Model Code |
Read/Write |
0~65535 |
|
40102 |
00 65 |
total number of measuring points |
read/write |
1~20 |
|
40103 |
00 66 |
device address |
read/write |
1~249 |
|
40104 |
00 67 |
baud rate |
read/write |
0~6 |
|
40105 |
00 68 |
communication mode |
read/write |
1~4 |
|
40106 |
00 69 |
protocol type |
read/write |
1~10 |
For example, the range is 0~1200W/M2, the analog output is 4~20mA current signal, Illuminance and current The calculation relationship is as shown in the formula: C = (A2-A1) * (X-B1) / (B2-B1) + A1, where A2 is Illuminance range upper limit, A1 is the lower limit of the range, B2 is current output range upper limit, B1 is the lower limit, X is the currently read Illuminance value, and C is the calculated current value. The list of commonly used values is as follows:
|
current(mA) |
IlluminanceValue (W/M2) |
Calculation Process |
|
4 |
0.0 |
(1200-0)*(4-4)÷(20-4)+0 |
|
5 |
75.0 |
(1200-0)*(5-4)÷(20-4)+0 |
|
6 |
150.0 |
(1200-0)*(6-4)÷(20-4)+0 |
|
7 |
225.0 |
(1200-0)*(7-4)÷(20-4)+0 |
|
8 |
300.0 |
(1200-0)*(8-4)÷(20-4)+0 |
|
9 |
375.0 |
(1200-0)*(9-4)÷(20-4)+0 |
|
10 |
450.0 |
(1200-0)*(10-4)÷(20-4)+0 |
|
11 |
525.0 |
(1200-0)*(11-4)÷(20-4)+0 |
|
12 |
600.0 |
(1200-0)*(12-4)÷(20-4)+0 |
|
13 |
675.0 |
(1200-0)*(13-4)÷(20-4)+0 |
|
14 |
750.0 |
(1200-0)*(14-4)÷(20-4)+0 |
|
15 |
825.0 |
(1200-0)*(15-4)÷(20-4)+0 |
|
16 |
900.0 |
(1200-0)*(16-4)÷(20-4)+0 |
|
17 |
975.0 |
(1200-0)*(17-4)÷(20-4)+0 |
|
18 |
1050.0 |
(1200-0)*(18-4)÷(20-4)+0 |
|
19 |
1125.0 |
(1200-0)*(19-4)÷(20-4)+0 |
|
20 |
1200.0 |
(1200-0)*(20-4)÷(20-4)+0 |
As shown in the above formula, when measuring 8mA, current current is 304W/M2。
For example, the range is 0~1200W/M2, the analog output is 0~10V DC0-10Vvoltage signal, Illuminance and DC0-10Vvoltage The calculation relationship is as shown in the formula: C = (A2-A1) * (X-B1) / (B2-B1) + A1, where A2 is Illuminance range upper limit, A1 is the lower limit of the range, B2 is DC0-10Vvoltage output range upper limit, B1 is the lower limit, X is the currently read Illuminance value, and C is the calculated DC0-10Vvoltage value. The list of commonly used values is as follows:
|
DC0-10Vvoltage(V) |
IlluminanceValue (W/M2) |
Calculation Process |
|
0 |
0.0 |
(1200-0)*(0-0)÷(10-0)+0 |
|
1 |
120.0 |
(1200-0)*(1-0)÷(10-0)+0 |
|
2 |
240.0 |
(1200-0)*(2-0)÷(10-0)+0 |
|
3 |
360.0 |
(1200-0)*(3-0)÷(10-0)+0 |
|
4 |
480.0 |
(1200-0)*(4-0)÷(10-0)+0 |
|
5 |
600.0 |
(1200-0)*(5-0)÷(10-0)+0 |
|
6 |
720.0 |
(1200-0)*(6-0)÷(10-0)+0 |
|
7 |
840.0 |
(1200-0)*(7-0)÷(10-0)+0 |
|
8 |
960.0 |
(1200-0)*(8-0)÷(10-0)+0 |
|
9 |
1080.0 |
(1200-0)*(9-0)÷(10-0)+0 |
|
10 |
1200.0 |
(1200-0)*(10-0)÷(10-0)+0 |
As shown in the above formula, when measuring 5V, current DC0-10Vvoltage is 600W/M2。